PC-UPROG UNIVERSAL PROGRAMMER COPYRIGHT NOTIC This documentation and the software routines contained in the PC-UPROG software diskette are copyrighted, 1990 - 1995 by Advantech Co. , Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements to the product described in this manual a time without notice .No part of this manual may be reproduced,copied,translated or transmitted , in any form, or by any means ,without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. However, Advantech Co., Ltd. assumes responsibility for its use; nor for any infringements of rights of third parties which may result from its use. ACKNOWLEDGEMENTS PC-UPROG is a trademark of Advantech Co. Ltd. IBM and PC are trademarks of Internationa Business Machines Corporation. MS-DOS is a trademark of Microsoft Corporation. Rev. A2 In Taiwan Aug. 1991 1. INSTALLATION 1.1. Changing your CONFIG.SYS file Since PC-UPROG opens up to 10 file during operation, the system will return an error if the FILES parameter of CONFIG.SYS file is less than 15 ( DOS already using 5 files ). The CONFIG.SYS file may be edited with any ASCII text editor. 1.2. Software Installation The PC-UPROG software is distributed on one 720k diskette. The diskette initially contains only two files. INSTALL.EXE 15K bytes INSTALL.DAT 306K bytes First you should make a backup copy of the diskette (the PC UPROG software is not copy protected). Keep the master diskette in a safe place (there is a nominal fee for replacement of lost disks). Boot your system with your standard DOS boot diskette or hard disk. If your system has a hard disk, insert PC-UPROG diskette into your floppy drive and type INSTALL C: The install utility will create the directory '\PC-UPROG' on your hard disk, and install the following files. pc-uprog.dev pc-uprog.dmp pc-uprog.pin pc-uprog.fam pc-uprog.wav pc-uprog.hlp pc-uprog.exe extuprog.dev extuprog.dmp extuprog.pin extuprog.fam extuprog.wav extuprog.hlp extuprog.exe The install utility will then test the hardware to verify the programmer unit and PC adapter card are installed correctly. If any error occurs, repeat the hardware installation process and try again. For floppy disk installation, insert PC-UPROG diskette into drive A: and the destination diskette into drive B: Then type INSTALL B: After you have finished installation, go to directory '\PC-UPROG' and type 'PC-UPROG'.The system will now display the main menu and you may now refer to 'OPERATION' section of this manual for details on specific programming procedures, etc. After exiting PC-UPROG (extuprog.exe)software, PC-UPROG will have created two files. pc-uprog.opt (extuprog.opt) pc-uprog.$$$ (extuprog.$$$) '*.opt' contains the software I/O port base address an last device selected. '*.$$$' is the device data edit buffer. 1.3. Starting PC-UPROG Power-on your computer. If using a hard disk, select the "\PC-UPROG" directory. If using a floppy based system, insert your copy of the PC-UPROG software into the floppy disk drive. Then enter the command: C:\>PC-UPROG [XXX] [XXX]: Option for user selecting the I/O port base address, if no address parameter typing then PC-UPROG will use the I/O port base address stored in pc-uprog.opt file (or use factory setting address 300 hex in the first time execution). The PC-UPROG main menu will be displayed. 1.4. Ordering Information PC-UPROG PC-based universal programmer, including universal programmer unit, PC adapter card (PCL-560A), system interface cable Accessories furnished: System disk Operations manual PCL-560A Additional PC adapter card for PC-UPROG PLCC-2020-01 20-pin PLCC to 20-pin DIP adapter for GAL or PAL 16XX series PLCC-2824-04 28-pin PLCC to 24 pin DIP adapter no connection pin on (1,8,15,22) for GAL or PAL 20XX series PLCC-2824-05 28-pin PLCC to 24 pin DIP adapter no connection pin on (5,8,11,19) for GAL or PAL 20XX series PLCC-3228-01 32-pin PLCC to 28 pin DIP adapter no connection pin on (1,12,17,26) PLCC-3228-11 32-pin PLCC to 28-pin DIP adapter for EPROM less than 512KB. PLCC-3232-01 32-pin PLCC to 32-pin DIP adapter PLCC-3232-11 32-pin PLCC to 32-pin DIP adapter for EPROM from 1M to 8M PLCC-4440-01 44-pin PLCC to 40-pin DIP adapter for 16 bit EPROM such as 27C1024 PLCC-4440-02 44-pin PLCC to 40-pin DIP adapter for 8751 series.UP NC(1,12,23,34). PLCC-4440-08 44-pin PLCC to 40 pin DIP adapter for 16 bit EPROM no connection pin on (1, 13, 23, 33) PLCC-4428-01 44-pin PLCC adapter for AMD MACH110/210/215 devices PLCC-4428-02 44-pin PLCC adapter for Lattice pLSI/ispLSI 1016 devices PLCC-6828-01 PLCC for AMD MACH 120/220 PLCC-6828-02 68-pin PLCC adapter for Lattice pLSI/ispLSI 1024 devices PLCC-8424-01 PLCC for AMD MACH 130/230/435 PLCC-8428-02 84-pin PLCC adapter for Lattice pLSI/ispLSI 1032 devices PLCC-EP610 28-pin PLCC socket for EP610,special adapter for ALtera PLCC-6840-01 68-pin PLCC to 40 pin DIP adapter for ALtera EP18XX series PLCC-ATV2500 PLCC/DIP socket for Atmel ATV2500/ Signetics PLV2500 AD16C54 DIP for MicroChip 16C54/55/56/57/71/84 AD68705 Motorola 68705 P3/P5, U3/U5, R3/R5 adapter AD68705C8/C9 Motorola 68705C8/C9 adapter AD87C751 Signetic 87C750/751/752 adapter AD86E21 Zilog Z86E21 adapter AD86E30/40 DIP for Zilog Z86E30/Z86E40 ADEPM5016 Altera EPM5016/32 DIP Adapter ADEPM7032 Altera EPM7032 DIP Adapter ADPSD301 44 pin PLCC for PSD3XX Series adapter ADPSD401 68 pin PLCC for PSD4XX/5XX Series adapter AT-101/A UV-ERASER with timer (30 devices maximun) AT-102/A Portable UV-ERASER with timer (12 devices maximun) PALASM 90 PLD software design package 1.5. DEVICES NEED ADAPTERS AMD MACH110/210/215/120/220/130/230/435 Motorola M68705P3/P5/U3/U5/R3/R5/C8/C9 M68HC11 Philips 87C750/751/752/451/452/552/054/592 PLV2500 Zilog Z86E21/E30/E40 Z86E08 SGS-Thomas Z86E21 Micro-chip PIC16C54/55/56/57/71/84 PIC17C42 Altera EP1800/1810/1830/5016/5032/7032 ATV2500/B TI EP1810/1830 Intel 5C180,28F002-B/T,28F200-B/T,28F004-B/T,28F400-B/T Waferscale PSD301/311/311C1,PSD302/312/312C1,PSD303/313/313C1, PSD401/411A1,PSD401/411A2,PSD402/412A1,PSD402/412A2, PSD403/413A1,PSD403/413A2,PSD501/511B1,PSD502/512B1, PSD503/513B1. Xilinx XC7236/7236A,XC7272/7272A,XC7336,XC7354.